- Júniusban Magyarországra érkezik a Tecno, a fejlődő piacok egyik kedvenc márkája
- Samsung Galaxy A54 - türelemjáték
- Nokia 3210 - felélni az örökséget
- Samsung Galaxy S24 Ultra - ha működik, ne változtass!
- Google Pixel 6/7/8 topik
- Huawei Watch Fit 3 - zöldalma
- Apple iPhone 13 mini - miért nem veszik elegen?
- Jobb zoom, egyszerűbb kijelző - megérkezett a Sony Xperia 1 VI
- Drágábban indíthat az új iPhone SE
- Samsung Galaxy S23 Ultra - non plus ultra
Hirdetés
-
Megjött az ASUS 240 Hz-es, fényes WOLED monitora
ph Az MI-s képességekkel felvértezett újdonság 20 százalékkal jobb fénysűrűséget produkál az egész képátlón átívelve, mint a PG27AQDM.
-
Az Apple szerint ejteni kell az USA trösztellenes perét
it Az Apple megkért egy bírót, hogy ejtse az USA igazságügyi minisztériumának és 15 amerikai államnak az ellene indított, trösztellenes perét. Azt is megmondták, hogy miért.
-
Ismét mozgásban a Kingmakers
gp Továbbra is izgatottan várjuk a játékot, amelyben a középkorba utazunk modern fegyverekkel.
-
Mobilarena
Minden ami szünetmentes tápegységgel (UPS-sel) kapcsolatos. Ha kérdésed van akár készülék vásárlással, akár hibával kapcsolatban, vagy csak tanácsot kérnél, írd meg ide, és lesz aki segít!
Új hozzászólás Aktív témák
-
xeri
tag
válasz lajos001 #708 üzenetére
Szerintem erre gondolsz:
5.5 Option switches
The UPS has a set of four DIP switches on the rear panel which allow you
to configure several options (see Secs. 5.5.1–5.5.4).
0 (off) I (on)
1
2
3
4
Note: You can set option switches at any time, and the effect is immediate.
Note: If all of the option switches are set to the on position, the option switches are
disabled. However, the functions controlled by the option switches are still
available using UPS monitoring software (see Sec. 5.6.4).
5.5.1 Option Switch 1
The UPS contains utility fault detection circuitry that is extremely sensitive
to line voltage distortions including spikes, notches, sudden dips, and
swells. The UPS is factory-set to react to such line voltage distortions by
immediately transferring the load to on-battery operation, affording
maximum protection for all load types. Where power quality is poor
because of local cyclic heavy load-switching, or the use of inexpensive fuel
generators, the UPS may frequently transfer to on-battery. If the UPS is
powering loads that operate normally under such conditions, battery
capacity may be spent unnecessarily.
Setting Option Switch 1 to the on ( I ) position desensitizes the UPS to rapid
low-amplitude line-voltage fluctuations, and increases the UPS’s upper
transfer voltage by 3%, for a total of 13% above the nominal input voltage.
This helps maintain maximum battery capacity for major utility failures.
20
5.5.2 Option Switch 2
Option Switch 2 functions differently for different versions of the UPS.
n 100 Vac version
No function; not used.
n 120 Vac version
The UPS’s factory-set input voltage limits for on-line and SmartBoost
operation are centered on the nominal input voltage of 120 Vac (see also
Sec. 9.1). When Option Switch 2 is set to the on ( I ) position, the upper and
lower transfer voltages are lowered by 4% and centered on a nominal input
of 115 Vac. This is useful where nominal input voltage is 110 to 115 Vac.
n 220/230/240 Vac version
The UPS’s factory-set on-battery output voltage and input voltage limits for
on-line and SmartBoost operation are designed for use in regions where the
nominal line voltage is 220 to 230 Vac. When Option Switch 2 is set to the
on ( I ) position, the upper and lower transfer voltages are raised by 4% and
centered on a nominal input of 240 Vac. In addition, the on-battery output
voltage is increased to 240 Vac.
5.5.3 Option Switch 3
When Option Switch 3 is set to the on ( I ) position, the UPS’s audible alarm
is disabled for the first 30 seconds of on-battery operation. This function is
useful where brief power interruptions are frequent and cause the alarm to
become annoying.
5.5.4 Option Switch 4
When Option Switch 4 is set to the on ( I ) position, the UPS’s low-battery
alarm interval is extended from 2 minutes (factory setting) to 5 minutes.
This function is useful if the UPS is protecting a computer system that
requires more than 2 minutes warning to perform a graceful shutdown.
Az idézet innen való, érdemes friss tulajdonosként átböngészned: [link]
Új hozzászólás Aktív témák
- Júniusban Magyarországra érkezik a Tecno, a fejlődő piacok egyik kedvenc márkája
- Ingatlanos topic!
- Samsung Galaxy A54 - türelemjáték
- Nokia 3210 - felélni az örökséget
- AMD Catalyst™ driverek topikja
- Milyen TV-t vegyek?
- Windows 11
- Egy utolsó platformmal egészíti ki a negyedik generációs EPYC családot az AMD
- Windows Insider Program
- Samsung Galaxy S24 Ultra - ha működik, ne változtass!
- További aktív témák...
Állásajánlatok
Cég: Ozeki Kft.
Város: Debrecen
Cég: Ozeki Kft.
Város: Debrecen