- Android alkalmazások - szoftver kibeszélő topik
- Samsung Galaxy S21 és S21+ - húszra akartak lapot húzni
- Poco F5 - pokolian jó ajánlat
- Ismét egyedit alkotott a Sharp
- Motorola Edge 40 - jó bőr
- Mobil flották
- Xiaomi 12T - egytucat
- Fotók, videók mobillal
- Xiaomi 11 Lite 5G NE (lisa)
- Ezek a OnePlus 12 és 12R európai árai
Hirdetés
-
Tetőfokára hág a tavasz, és ezt a hardverek is érzik
ph Asztali PC-k, monitorok, videokártya, hát, hűtés és egér is került heti válogatásunkba.
-
Már nem hisz a nagy európai EV-forradalomban a Ford
it Meggondolta magát a Ford, a helyzetre való tekintettel 2030 után is kínálhat Európában hibrid és benzines autókat.
-
Ghost of Tsushima - A PC-s kiadás több mint 170 régióban elérhetetlen lesz
gp Hasonlóan a Helldivers II-höz, ahol nincs PSN regisztrációra lehetőség, ott nem lehet megvenni a programot.
Új hozzászólás Aktív témák
-
tothbe
addikt
válasz DJ.Gróf #2327 üzenetére
Kell neki egy hidegreset az törli a network beállításokat is default-ra.
aztán meg a Web JetAdmin-t használva be tudod állítani bármire.Hidegreset lépései:
Kikapcs
Nyomod és nyomva tartod a pici TÖRLÉS/CANCEL gombot.
Bekapcsolod és mikor minden led világít elengeded a cancel-t.
(Ha nem engeded el 20 mp-en belül a ledek felvillanásától számítva, akkor nem hidegreset hanem NVRAM inicializáció lesz helyette.)De van itt egy angol leirás is, ami több opciót is kinál.
You have several alternatives:The easiest and fastest way to do this is to plug the JD into a printer with a LCD control panel, and configure the JD for either DHCP or a static config, whichever is appropriate for your network. (Already discussed above.)
I have a few of these on my network, so I am quite familiar with them. Here are the cold reset instructions, which need to be followed very carefully:
Cold Reset both printer and JetDirect, LJ2100:
1. Power off and unplug the printer from the wall. Unplug network cable.
2. Press (and hold) the small (Job Cancel) button on top of the printer, power the printer back on.
3. When the printer lights come ON, release the button. (If you hold the button down too long, NVRAM will be reset, which you do not want to do.) Allow the printer to power on fully.
Press both control panel buttons briefly at the same time to print the two config pages. The JD config page should show 0.0.0.0 for the IP address.
At this point, you could use Web JetAdmin to configure the TCP/IP settings.
Another method is to use a cross-over patch cable, connecting the JD directly to your PC's network card. So the printer and the PC are their own little network. Configure a static IP address for the PC. Set the subnet mask and gateway the same as you see on the JD config page. You can now use WJA to change the JD configuration. (You need to have previously installed WJA.)
Remember to change the PC network config back to whatever it needs to be for your normal network operation.
By(e) Tothbe
Új hozzászólás Aktív témák
- Hisense LCD és LED TV-k
- Házimozi belépő szinten
- VR topik (Oculus Rift, stb.)
- Gitáros topic
- Megérkezett a Corsair új M.2-es SSD-je, és mindennek mondható, csak lassúnak nem
- Bocsánatot kért az Apple, mert nagyon mellélőtt a legutóbbi reklámjával
- Windows 11
- Programozás topic
- Android alkalmazások - szoftver kibeszélő topik
- Azonnali informatikai kérdések órája
- További aktív témák...
Állásajánlatok
Cég: Ozeki Kft.
Város: Debrecen
Cég: Promenade Publishing House Kft.
Város: Budapest