- Redmi Note 13 Pro+ - a fejlődés íve
- Samsung Galaxy S23 Ultra - non plus ultra
- Redmi Note 12 4G - valaki fizetni fog
- Android alkalmazások - szoftver kibeszélő topik
- Samsung Galaxy S23 és S23+ - ami belül van, az számít igazán
- Apple iPhone 15 Pro Max - Attack on Titan
- iPhone topik
- Macrodroid
- Huawei Mate 40 Pro - a csúcson kell abbahagyni?
- Poco X6 5G - egy Redmi álruhában
Hirdetés
-
AMD Radeon undervolt/overclock
lo Minden egy hideg, téli estén kezdődött, mikor rájöttem, hogy már kicsit kevés az RTX2060...
-
Három éve fontos döntést hozott az AI-ról az Apple
it A Bloomberg szerint saját chipekkel működtetné az AI-szervereket az Apple.
-
Enduro változatot kapott a Mobvoi TicWatch Pro 5
ma WearOS 3.5 rendszerrel és kettős FSTN és AMOLED kijelzővel érkezik az új modell.
-
Mobilarena
TP-Link WR1043ND - N450 router
Új hozzászólás Aktív témák
-
Beri
addikt
válasz zsolt501 #581 üzenetére
Az, amiről én tettem fel screenshotot, alapból benne van a dd-wrt-ben. Letöltöd a bin-t, gyári fw-ben kiválasztod, hogy upgrade, kiválasztod a bin-t, katt, vársz, örülsz
Geree: Igen, le kell vágni a fájl elejét. Idézet a dd fórumból:
I've flash back the original firmware sucessfully.What I did was:
1) I've dl the original fw from TP-Link.
2) Cut-off the first 0x20200 bytes so that the resulting file starts with the hex sequence:
01 00 00 00 54 50 2D3) I copied the new firmware into a usb pen drive (FAT).
4) Enabled usb in the DD-WRT firmware, with auto-mount.
5) Plugged the usb pen drive into the router and logged in by telnet.
6) Changed to /tmp directory (I'm not sure if this is really necessary).
7. Gave the following command.
mtd -e linux -r write /mnt/<firmwarefilename.bin> linux
where <firmwarefilename.bin> is the filename of the original firware stripped of the 0x20200 first bytes. In my case, I named it 0x20200.bin /mnt is the mount point. My firmware was located on the root directory.
This is what you're going to get:
root@WR1043ND:/tmp# mtd -e linux -r write /mnt/0x20200.bin linux
Unlocking linux ...
Erasing linux ...
Writing from /mnt/0x20200.bin to linux ... [w]Connection to host lost.
Press any key to continue...
Amire még oda kell figyelni:
Reset DD-WRT to factory default before you flash TP-LINK FW with mtd command.Make sure you do "cd /tmp" before the mtd command.
Verify that you your cutted file with only "header + firmware" from last TP-LINK firmware has one of these checksums:
MD5: E712A4A274765A8E63E4B84AA2BCA99E
SHA1: 8B20344B19160006355F02A6BCC895353F4A4A2E
CRC32: 13820BE6When I flashed from tplink to ddwrt FW:
I first flashed "factory-to-ddwrt.bin" from tplink webui.
After that I flashed "tl-wr1043nd-webflash.bin" from ddwrt webui.
"tl-wr1043nd-webflash.bin" was the FW in my router before I went back to tplink fw.After I flashed from ddwrt to tplink using mtd, I reflashed the full tplink FW from tplink webui to make sure I flashed tplink uboot.
eladó Aromamizer RDTA V1
Új hozzászólás Aktív témák
- Fallout 4
- Intel Core i5 / i7 / i9 "Alder Lake-Raptor Lake/Refresh" (LGA1700)
- Visszavonta az Intel és a Qualcomm Huawei-hez kiadott exportlicencét az USA
- exHWSW - Értünk mindenhez IS
- Xbox 360
- bb0t: Gyilkos szénhidrátok, avagy hogyan fogytam önsanyargatás nélkül 16 kg-ot
- LEGO klub
- Autóápolás, karbantartás, fényezés
- GTA V
- Reklámblokkolók topikja
- További aktív témák...
Állásajánlatok
Cég: Promenade Publishing House Kft.
Város: Budapest
Cég: Ozeki Kft.
Város: Debrecen